Download Previous year Diploma Paper of Elements of Desgin 5th Sem Dec 2015 Automobile Diploma Paper
Elements of Desgin 5th Sem Dec 2015 Automobile Diploma Paper
                SECTION-A
Q.1 FILL IN BLANKS
I. Mass production is possible due to ____________
II. The unit of stress is ____________
III. For H8-h8 lit minimum clearance is ____________
IV. A basic hole is one whose _________ deviation is zero
V. Lack of ductility ______________ .
VI. Muff coupling is designed as ____________ shaft
VII. The maximum shear stress theory is used for _________ materials
VIII. The design of the shaft is based ___________ and rigidity
IX. Energy is absorbed by fly wheel virtue of its ____________
X. In a flange coupling hub is designed as _____________ shaft
TRUE/FALSE
XI. A centrifugal clutch works on the principle of centrifugal force
XII. Knuckle joint is a permanent fastening
XIII. A keyway lowers the strength of the shaft
XIV. Two intersecting shafts can be connected by spur gear
XV. A cotter joint is used to transmit axial tensile or compressive load.
       SECTION-B
Q2. Attempt any five questions.                                  5×6=30
Q2. (a) A solid steel shaft transmits a power of 90 kw at 240 rpm .Taking working stress As 75 mpa find suitable diameter of shaft. if maximum torque transmitted in each Revolution exceeds the mean torque by 20% .find the outer diameter of shaft Where inside is 0.8 times of outside diameter which replaces the solid shaft.
(b) Write a short note on following
(i) Standardization
(ii) Interchangeability
(c) A solid circular shaft is subjected to a bending moment of 3.46 KN-m and a torsional moment
of 11.5 KN-m.The shaft is made up of C45 steel and factor of safety is 6.Determine the diameter of shaft.the ultimate shear stress is 500 Mpa
(d) Discuss the phenomenon of creep briefly.
(e) What do you understand by coupling? Explain its function and advantages.
(f) What are keys? Explain any five types of keys through neat and clean Diagram. Also discuss their uses.
(g) What is function of clutch? Describe briefly various types of clutches.
(h) What do you understand by design and types of design also explain design Procedure.
                 SECTION-C
Q3. Attempt any three questions.                            3×10=30
a) Assuming uniform wear ,determine the maximum, minimum and average pressure in a plate clutch when the axial force is 7KN.The inside radius of the contact surface is 50 mm and outside radius is 100 mm
b) Design and draw a protective type flange coupling for a steel shaft transmitting 14 kw at 260 rpm and having allowable shear stress 42 mpa the working stress in bolt should not exceed 30 mpa. Assume the same material is used for shaft and key and crushing stress is twice the shearing stress .the maximum torque is 20% greater than full load torque. the shear stress for cast iron is 14 mpa
c) Design a knuckle joint to transmit an axial load of 140kn assume the working stress For both pin and rod material as 80 n/mm2 in tension, 68 n/mm2 in shear and 160 N/mm²in crushing.
Elements of Desgin 5th Sem DEC 2015 Automobile Diploma Paper
Get StartedSection a Elements of Desgin 5th Sem DEC 2015 Automobile Paper
Mass production is possible due to ____________Mass production is possible due to ____________
The unit of stress is ____________
For H8-h8 lit minimum clearance is ____________
A basic hole is one whose _________ deviation is zero.
Lack of ductility ______________ .
Muff coupling is designed as ____________ shaft.
The maximum shear stress theory is used for _________ materials.
The design of the shaft is based ___________ and rigidity.
Energy is absorbed by fly wheel virtue of its ____________
In a flange coupling hub is designed as _____________ shaft
A centrifugal clutch works on the principle of centrifugal force.T/F
A keyway lowers the strength of the shaft.T/F
Elements of Desgin 5th Sem Dec 2015 Automobile Diploma Paper Click Here
Section B :Elements of Desgin 5th Sem dEC 2015 Automobile Paper
A solid steel shaft transmits a power of 90 kw at 240 rpm .Taking working stress As 75 mpa find suitable diameter of shaft.Solid steel shaft transmits a power of 90 kw at 240 rpm .Taking working stress As 75 mpa find suitable diameter of shaft. if maximum torque transmitted in each Revolution exceeds the mean torque by 20% .find the outer diameter of shaft Where inside is 0.8 times of outside diameter which replaces the solid shaft.
Short note on following
(i) Standardization
(ii) Interchangeability
Solid circular shaft is subjected to a bending moment of 3.46 KN-m and a torsional moment
of 11.5 KN-m.The shaft is made up of C45 steel and factor of safety is Determine the diameter of shaft.the ultimate shear stress is 500 Mpa
Phenomenon of creep briefly.
Coupling and its function and advantages.
Keys and any five types of keys through neat and clean Diagram.Â
Function of clutch.
Various types of clutches.
Design and types of designÂ
Elements of Desgin 5th Sem Dec 2015 Automobile Diploma Paper Click Here
Elements of Desgin 5th Sem dec 2015 Automobile Diploma Paper
Get Started https://www.youtube.com/watch?v=UHX6f8TIvX8https://www.youtube.com/watch?v=M_RR6LVICp0https://www.youtube.com/watch?v=mV41CMWonN4https://www.youtube.com/watch?v=s0LVPE0Q3LE&list=PLA9Q9SDZ781WXNAWit379A4CRLMvjGiUw&index=14&t=0sSection c :-Elements of Desgin 5th Sem dec 2015 Diploma Paper
Assuming uniform wear ,determine the maximum, minimum and average pressure in a plate clutch when the axial force is 7KN.The inside radius of the contact surface is 50 mm and outside radius is 100 mma) Assuming uniform wear ,determine the maximum, minimum and average pressure in a plate clutch when the axial force is 7KN.The inside radius of the contact surface is 50 mm and outside radius is 100 mm
A Design and draw a protective type flange coupling for a steel shaft transmitting 14 kw at 260 rpm and having allowable shear stress 42 mpa the working stress in bolt should not exceed 30 mpa. Assume the same material is used for shaft and key and crushing stress is twice the shearing stress .the maximum torque is 20% greater than full load torque. the shear stress for cast iron is 14 mpa
Design a knuckle joint to transmit an axial load of 140kn assume the working stress For both pin and rod material as 80 n/mm2 in tension, 68 n/mm2 in shear and 160 N/mm²in crushing.
Elements of Desgin 5th Sem Dec 2015 Automobile Diploma Paper Contact Us
MY YOUTUBE CHANNEL
JK Smart Classes Upload Lecture for Degree classes like B.TECH,M.TECH in any stream like ECE,EE,ME and Civil Engineering![\"JK](\"https://www.psbtepaper.com/wp-content/uploads/2020/03/JK-SMART-CLASSES-removebg-preview-1.jpg\")
JK SMART CLASSES
ER.JASWINDER KUMAR
JK SMART LECTURE
ER.JASWINDER KUMAR
Engineering Classes Upload Lecture for Polytechnic Diploma classes in any stream like ECE,EE,ME and Civil Engineering
ENGINEERING CLASSES
ER.JASWINDER KUMAR
er.jaswinder kumar
Senior Lecturer